Search Results

This paper compares the emissions performance of four ultra thin wall ceramic substrates with standard wall thickness product on a chassis dynamometer for two different substrate volumes. This comparison helps establish performance trends and provides useful information for selection of substrates in designing catalytic converter systems. This experimental study tests and compares four ultra thin wall products (400/4, 600/3, 600/4, and 900/2) with a standard wall product (400/6.5) at two different substrate volumes. Engine bench aging is used to simulate typical aged conditions. Temperature data as well as second by second and bag emissions data for hydrocarbons, carbon monoxide and oxides of nitrogen were used to evaluate the relative performances of the substrates. The US FTP and US06 driving cycles were used as protocols for the comparison. Results suggest that lower bulk density and higher geometric surface area interact to lead to lower emissions.

To establish performance trends in ultra thin wall substrates and help support their selection criteria for designing catalytic converter systems, the light-off behavior of five Ultra Thin Wall ceramic substrates and two catalysts on an engine dynamometer are hereby examined. Modeling predictions are also compared to the engine results and the trends and implications are discussed. To quantify the performance of these different systems, light-off tests were performed on an engine dynamometer using a simulated FTP cycle. Five systems were evaluated (600/4, 600/3, 600/2, 900/2 and 1200/2) each with two different catalyst formulations. Engine bench aging was used to simulate typical aged conditions in the converter systems. Second by second emissions data for temperature, hydrocarbons and carbon monoxide, were used to evaluate the relative performances of the substrates.

In urban areas, particulate emission from diesel engines is one of the pollutants of most concern. As a result, particulate emission control from urban bus diesel engines using particle filter technology is being evaluated at several locations in the US. A project entitled, “Clean Diesel Vehicle Air Quality Project” has been initiated by NY City Transit under the supervision of NYSDEC and with active participation from several industry partners. Under this program, 25 NY City transit buses with DDC Series 50 engines have been equipped with continuously regenerating diesel particulate filter systems and have been operating with ultra low sulfur diesel (< 30 ppm S) in transit service in Manhattan since February 2000. These buses were evaluated over a 9 month period for operations, maintainability and durability of the particulate filter.

Quantitative in-use pressure measurements were taken from packaging ceramic substrates with the SoftMountSM technology and two more traditional technologies, stuffing and tourniquet. Each technology was assessed using four separate mat materials. Mat selection enhanced the application of the SoftMountSM technology through the reduced pressures applied to the substrate during packaging. High temperature and low temperature thermal cycling studies were performed on the canned converters for the three packaging technologies so that an evaluation could be made of converter durability. The SoftMountSM packaging technology yielded the lowest pressures of all the processes studied, regardless of mat type. The laminar hybrid mat evaluated yielded the best combination of pressure and durability performance. Low temperature residual shear strengths following thermal cycling of the converters showed good correlation between the SoftMountSM technology and the stuffing method.

Particulate emission from diesel engines is one of the most important pollutants in urban areas. As a result, particulate emission control from urban bus diesel engines using particle filter technology is being evaluated at several locations in the US. A project entitled “Clean Diesel Demonstration Program” has been initiated by NY City Transit under the supervision of NY State DEC and with active participation from several industrial partners. Under this program, several NY City transit buses with DDC Series 50 engines have been equipped with continuously regenerating diesel particulate filter system and are operating with ultra low sulfur diesel (< 30 ppm S) in transit service in Manhattan since February 2000. These buses are being evaluated over a 8-9 month period for operations, maintainability and durability of the particulate filter.

An analytical model for estimating shear and bending stresses during canning of cordierite ceramic catalyst supports is presented. These stresses arise when the radial pressure distribution is nonuniform due, primarily, to variations in gap bulk density (GBD ) of intumescent mat around the perimeter of the substrate. Variations in GBD can occur during canning, regardless of the canning technique, due to anisotropic can stiffness or component tolerances or mat overlap. The model helps relate shear and bending stresses to substrate size and orientation, elastic modulii, cell size and wall porosity. If these stresses approach the corresponding strength of substrate, a shear crack may develop during or after the canning process depending on the magnitude of stress. A special test fixture was developed to measure the shear strength of ceramic catalyst supports, with different cell sizes, before and after the application of washcoat.

It is well known that the catalytic efficiency and durability of an automotive catalytic converter can be significantly affected by its design. This paper demonstrates the potential for further improvement in both the durability and efficiency by using a novel catalytic converter concept based on a large frontal area, high cell density substrate. This concept requires that attention be paid to optimization of the flow as well as of the mounting system. The converter design is determined with a computational fluid dynamic (CFD) simulation and the effect of this design on the temperature distribution in the substrate is calculated and measured. Due to this novel converter concept the maximum substrate temperature is reduced, which results in a better aging behavior. This improvement allows a reduction in precious metal content without a loss in efficiency.

This paper gives a comprehensive overview of the current state-of-the-art in diesel emission control. The nature of diesel particulates is summarized. The variety of diesel particulate filter regeneration strategies that will become so important to filter application are reviewed. Filter retrofit and durability issues are addressed. DeNOx catalysts, SCR, NOx traps for diesel, and non-thermal plasma methods are summarized. Integrated NOx/PM systems are described. And reduction of exhaust toxics is discussed. The paper covers all major conferences in the year 2000 that occurred in the US and Europe. US and Europe.

As demand for wall-flow Diesel Particulate Filters (DPF) increases, accurate predictions of DPF behavior, and in particular their pressure drop, under a wide range of operating conditions bears significant engineering applications. In this work, validation of a model and development of a simulator for predicting the pressure drop of clean and particulate-loaded DPFs are presented. The model, based on a previously developed theory, has been validated extensively in this work. The validation range includes utilizing a large matrix of wall-flow filters varying in their size, cell density and wall thickness, each positioned downstream of light or heavy duty Diesel engines; it also covers a wide range of engine operating conditions such as engine load, flow rate, flow temperature and filter soot loading conditions. The validated model was then incorporated into a DPF pressure drop simulator.

Wall-flow Diesel particulate filters operating at low filtration velocities usually exhibit a linear dependence between the filter pressure drop and the flow rate, conveniently described by a generalized Darcy's law. It is advantageous to minimize filter pressure drop by sizing filters to operate within this linear range. However in practice, since there often exist serious constraints on the available vehicle underfloor space, a vehicle manufacturer is forced to choose an “undersized” filter resulting in high filtration velocities through the filter walls. Since secondary inertial contributions to the pressure drop become significant, Darcy's law can no longer accurately describe the filter pressure drop. In this paper, a systematic investigation of these secondary inertial flow effects is presented.

Honeycomb based diesel particulate filters have proven to be extremely effective in the removal of diesel soot. Under certain conditions, involving heavy soot loads and a shift of the engine into the idle mode during the early stages of the regeneration process, the current designs of cordierite filters have shown some tendency toward partial melting. A brief review of the SAE literature is presented, indicating that the temperatures reached during regeneration decrease substantially as the bulk heat capacity of the filter increases. Analysis of these literature data indicates that the top temperatures experienced during regeneration can be decreased by hundreds of degrees, by relatively modest increases in the bulk heat capacity of the bodies. New data are presented confirming how the top temperature varies with different filter designs in which the bulk heat capacity varies.

The key diesel emission control papers of the last 12 months have been summarized. In addition, the emerging US and European light-duty and heavy-duty tailpipe regulations are compared. Results are reported on light-duty diesel filtration regeneration systems and experiences, including effects of ash build-up and some recent modeling work. On the heavy-duty side, optimization of SCR catalysts and systems are described, as well as experiences with the first integrated SCR/filter systems, which are already achieving “Euro V” 2008 standards. An update on NOx adsorbers is also provided. The results with new NOx formulations are described, as well as the system performance in a light-duty diesel application.

This paper focuses on the effect of temperature on biaxial strength of curved, symmetrically laminated, automotive windshields. In view of their aspheric curvature, the measurement of biaxial strength requires a special ring-on-ring test fixture with compliant loading and support rings. The key factors that affect strength are (i) fatigue behavior of surface flaws, (ii) expansion mismatch between glass and PVB interlayer, and (iii) interfacial bond integrity. These, in turn, depend on the operating temperature which for automotive windshields can range from −40°C in winter to +50°C in summer. The data show that the biaxial strength is 21% higher at −40°C and 28% lower at +50°C than that at room temperature. An assessment of fatigue and interfacial bond integrity shows that strength changes of these magnitudes are predominantly caused by residual stresses arising from expansion mismatch between glass and PVB interlayer.

One approach to the remediation of NOx generated under lean automotive engine conditions is its controlled storage and then periodic release and reaction under enriched conditions. This process is being considered for automotive exhaust systems that will be operated pre–dominantly lean for reasons of fuel economy. Because of the special characteristics of alkali and alkaline earth elements in the presence of NOx, they are being considered for use, in conjunction with γ–alumina–based washcoats and precious metal catalysts, as NOx catalyst coatings on cellular supports. It is known that alumino–silicates will react with alkali and alkaline earth elements to form stable ceramic phases when mixtures of the components are held in direct contact at elevated temperatures.

A new converter concept is introduced, which utilizes the additional space in the inlet cone of the converter. An optimized design is obtained by the application of computational fluid dynamics (CFD) and flow distribution measurements, resulting in up to 20% improved flow distribution through the substrate. In addition, the volume of the converter can be increased by approximately 15% using the same space envelope. Durability tests of the converter system have been performed using a thermal cycling test on an engine test bench for 135 hours. No deterioration of the substrate or mounting system occurred. The emissions performance was evaluated on a stationary dynamometer. The impact of the flow distribution on the temperature field and the conversion behavior during light-off and steady state operation were investigated. Under the current testing conditions, no differences in light-off behavior were determined, despite significant differences in the temperature field.

With stricter emissions standards, low back pressure requirements, and 100,000 mile durability specifications, ceramic catalysts have undergone significant developments over the past few years. The thrust in the ceramics area has centered on thin-wall structures to minimize back pressure and on high cell density for rapid light-off in close-coupled applications. The thin-wall structures are extruded from low expansion cordierite ceramic with adequate strength and thermal shock resistance equivalent to those of standard cordierite substrate. Examples of thin-wall substrate include 350XT which is extruded from a very low expansion dense cordierite ceramic, and 400/4 and 600/4 cell structures extruded from a low expansion modified cordierite ceramic. This paper will focus on the high fatigue resistance, excellent conversion efficiency, and low back pressure of 350 XT substrates with advanced washcoat system.

Governing bodies world-wide are setting increasingly tighter emission standards to help improve air quality. US and Californian LEV/ULEV standards are pace setting, European Stage II legislation has just become effective. In Brazil, the upcoming 1997 standards are also demanding for tighter emission control. The monolithic ceramic honeycomb catalytic converter -for more than the past 20 years- has been a reliable key element in the automotive emission control systems. In order to help meet tightened emission regulation as well to satisfy even more stringent durability requirement, an advanced thinwall ceramic Celcor XT has been developed for increased geometric surface area and reduced backpressure. The product properties as well as FTP and ECE emission and durability test results are being described in this paper. Converter system durability is also determined by robust canning and mounting systems. A durable mounting concept, especially for preconverters, is being described.

Preliminary back pressure and adsorption performance results are reported for two activated carbon honeycomb materials. The carbon impregnated honeycomb (CIH) material is porous ceramic honeycomb with a complete impregnation and coating of activated carbon on all ceramic surfaces. It offers the potential to be a permanent odor filter in that it can be in situ electrically regenerated. It has adsorption performance similar to commercially available layered filters, but has much lower back pressure. The second material is an activated carbon honeycomb (ACH) and is not ceramic-based as is CIH. As such, it has much more activated carbon and superior adsorption performance. The back pressure is low, as with CIH. It has significant potential as a high-performing disposable odor filter.

The monolithic, large frontal area (LFA), extruded ceramic substrates for diesel flow-through catalysts offer unique advantages of design versatility, longterm durability, ease of packaging and low Cost [1, 2]*. This paper examines the effect of cell density and cell size on catalyst light-off performance, back pressure, mechanical and thermal durability, and the steady-state catalytic activity. The factors which affect these performance characteristics are discussed. Certain trade-offs in performance parameters, which are necessary for optimum systems design, are also discussed. Following a brief discussion of design methodology, substrate selection, substrate/washcoat interaction and packaging specifications, the durability data for ceramic flow-through catalysts are summarized. A total of over 18 million vehicle miles have been successfully demonstrated by ceramic LFA catalysts using the systems design approach.

Extruded metal honeycombs are used as electrically heated catalysts (EHCs). The durability requirements of this application make demands on high surface area, thin cross-section metal honeycombs. Significant durability improvements over previous extruded metal honeycomb EHCs have been achieved by material and package design changes. The product redesign was supported by finite element models and extensive testing. The redesigned EHC has passed severe laboratory and field testing. The tests include electrical cycling to 1000°C/1600 cycles, hot vibration to 60g/900°C and demanding on-vehicle exposure. Excellent durability of the extruded metal honeycomb has been demonstrated.